Repair

How to Fix Stick Drift on Your Controller

Stick drift usually starts small and gets worse. Here's what to try, from a one-minute settings change to replacing the stick, and how to tell which one you need.

Quick answer

Most stick drift comes from a worn or dirty stick sensor. Confirm it with a drift test, then try these in order:

  1. Raise the in-game deadzone
  2. Clean around the stick
  3. Recalibrate
  4. Replace the stick module
  5. Use the warranty

First, make sure it's drift

A camera that slowly turns on its own isn't always the stick's fault. A second controller left on, a remap in Steam Input, or a game's aim assist can all look like drift. A quick test tells you for sure.

Put the controller down, let go of both sticks, and measure where they rest. A healthy stick springs back to within a few hundredths of the center.

Test firstStick drift testLet go for 3 seconds and get a pass, warn or fail for each stick, plus the deadzone that would hide it.
Open the test

What your result means

ResultWhat to do
PassProbably not drift. Check your game's settings, Steam Input, and any other connected controllers.
WarnMild drift. Start with the deadzone, then cleaning.
FailClear drift. Cleaning may help for a while, but plan for a repair or a warranty claim.

01Raise the in-game deadzone

The deadzone is a small area around the center where the game ignores the stick. If the stick rests just outside it, the game reads that as movement. Make the deadzone a little bigger and the drift disappears.

The drift test gives you a starting value under Deadzone to hide it. Games use different scales, so a reading of 0.17 might be “17” or “17%” in a settings menu.

Change only the stick that drifts. Many games let you set the left and right deadzones separately. A bigger deadzone makes small aiming movements less precise, so keep the healthy stick as it is.

This is a workaround, not a fix. If the drift keeps growing, you'll keep raising the number.

02Clean around the stick

Dust and grime can work their way into the gap around the stick and push the sensor off center. Cleaning won't fix a worn sensor, but it's free and often helps.

  1. Turn the controller off and unplug it.
  2. Blow short bursts of compressed air into the gap around the base of the stick. Keep the can upright.
  3. Rotate the stick slowly while you do it, so air reaches every side.
  4. Push the stick to the edge and roll it around a few times to loosen anything left.
  5. Test again. If the resting distance drops, cleaning helped. You may need to repeat it now and then.
Don't open the controller yet. Opening it may void the warranty. Try everything that doesn't need a screwdriver first.

03Recalibrate

Calibration resets where the controller thinks the center is. It helps when the sensor is healthy but the center has shifted. It can't bring back a worn sensor.

Some platforms and apps offer stick calibration, such as Steam's controller settings on a PC, or the companion app for some third-party controllers. Follow the steps there, then run the drift test again to see whether anything changed.

We don't offer calibration on this site. Writing settings to a controller from a web page can go wrong, and a failed write is harder to undo than drift.

04Replace the stick module

If the drift comes back after cleaning, or the test fails right away, the sensor inside the stick is probably worn. It won't recover on its own.

On most controllers the stick module is soldered to the circuit board, so replacing it means desoldering the old one. Repair shops do this routinely. If you do it yourself, you'll need a soldering iron and some patience.

Replacement modules include Hall effect sticks, which measure position with magnets instead of contacts, so they don't wear the same way. A few controllers, like the DualSense Edge, have stick modules you can swap without any tools.

05Use the warranty

If your controller is still covered, contact the maker before you open it. Describe when the drift happens and how long it has been going on.

A test result helps. The drift test's Copy share link button saves the result, with the controller name and the measured numbers, inside a link you can paste into a support request.

Which fix should you try?

FixEffortHelps when
Raise deadzoneA minute in settingsDrift is mild and you just want it gone in one game
CleanAbout 10 minutesDust or grime has got around the stick
RecalibrateA few minutesThe center has shifted but the sensor is healthy
Replace moduleAn hour, or a repair shopThe sensor is worn and drift keeps coming back
WarrantyA few daysThe controller is still covered
After any fixCheck that it workedRun the drift test again and compare the resting distance with your first result.
Test again